mirror of
https://github.com/kennetek/gridfinity-rebuilt-openscad.git
synced 2024-11-22 16:30:50 +00:00
53 lines
3 KiB
Markdown
53 lines
3 KiB
Markdown
# Gridfinity Rebuilt in OpenSCAD
|
|
|
|
[![CC BY-NC-SA 4.0][cc-by-nc-sa-shield]][cc-by-nc-sa]
|
|
|
|
A ground-up port (with a few extra features) of the stock [gridfinity](https://www.youtube.com/watch?v=ra_9zU-mnl8) bins in OpenSCAD. Open to feedback, because I could not feasibly test all combinations of bins. I tried my best to exactly match the original gridfinity dimensions, but some of the geometry is slightly incorrect (mainly fillets). However, I think they are negligible differences, and will not appear in the printed model.
|
|
|
|
Full documentation can be found at the project's [website](https://kennetek.github.io/gridfinity-rebuilt-openscad/).
|
|
|
|
The project can also be found on [Printables](https://www.printables.com/model/274917-gridfinity-rebuilt-in-openscad) if you want to support the project.
|
|
|
|
[<img src="./images/base_dimension.gif" width="320">]()
|
|
[<img src="./images/compartment_dimension.gif" width="320">]()
|
|
[<img src="./images/height_dimension.gif" width="320">]()
|
|
[<img src="./images/tab_dimension.gif" width="320">]()
|
|
[<img src="./images/holes_dimension.gif" width="320">]()
|
|
[<img src="./images/custom_dimension.gif" width="320">]()
|
|
|
|
## Features
|
|
- any size of bin (width/length/height)
|
|
- height by units, internal depth, or overall size
|
|
- any number of compartments (along both X and Y axis)
|
|
- togglable scoop
|
|
- togglable tabs, split tabs, and tab alignment
|
|
- togglable holes (with togglable supportless printing hole structures)
|
|
- manual compartment construction (make the most wacky bins imaginable)
|
|
- togglable lip (if you don't care for stackability)
|
|
- dividing bases (if you want a 1.5 unit long bin, for instance)
|
|
- removed material from bases to save filament
|
|
- vase mode bins
|
|
|
|
### Printable Holes
|
|
The printable holes allow your slicer to bridge the gap inside the countersunk magnet hole (using the technique shown [here](https://www.youtube.com/watch?v=W8FbHTcB05w)) so that supports are not needed.
|
|
|
|
[<img src="./images/slicer_holes.png" height="200">]()
|
|
[<img src="./images/slicer_holes_top.png" height="200">]()
|
|
|
|
## Recommendations
|
|
For best results, use a version of OpenSCAD with the fast-csg feature. As of writing, this feature is only implemented in the [development snapshots](https://openscad.org/downloads.html). To enable the feature, go to Edit > Preferences > Features > fast-csg. On my computer, this sped up rendering from 10 minutes down to a couple of seconds, even for comically large bins.
|
|
|
|
## Enjoy!
|
|
|
|
[<img src="./images/spin.gif" width="160">]()
|
|
|
|
[Gridfinity](https://www.youtube.com/watch?v=ra_9zU-mnl8) by [Zack Freedman](https://www.youtube.com/c/ZackFreedman/about)
|
|
|
|
This work is licensed under the same license as Gridfinity, being a
|
|
[Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License][cc-by-nc-sa].
|
|
|
|
[![CC BY-NC-SA 4.0][cc-by-nc-sa-image]][cc-by-nc-sa]
|
|
|
|
[cc-by-nc-sa]: http://creativecommons.org/licenses/by-nc-sa/4.0/
|
|
[cc-by-nc-sa-image]: https://licensebuttons.net/l/by-nc-sa/4.0/88x31.png
|
|
[cc-by-nc-sa-shield]: https://img.shields.io/badge/License-CC%20BY--NC--SA%204.0-lightgrey.svg
|